Set intel_idle.max_cstate=1 in /etc/default/grub, and then sudo update-grub and reboot solved the problem. If not found, add vm.swappiness=10 at the end of the file If found, edit it to say vm.swappiness=10 Search for an existing vm.swappiness= entry. Set vm.swappiness=10 (based on 32G RAM and 4G SWAP), this way. Since you have 32G RAM, to minimize swapping, let's change this value. To edit, use sudo -H gedit /etc/fstab or sudo pico /etc/fstab /swapfile none swap sw 0 0 Sudo chmod 600 /swapfile # set proper file protectionsĬonfirm this /swapfile line at the end of /etc/fstab. Hello, I try to set swapiness to 0 but it goes back to 10 after a reboot. Sudo dd if=/dev/zero of=/swapfile bs=1M count=4096 Sudo rm -i /swapfile # remove old /swapfile As the /etc/nf file is used to override default kernel parameter values, only a small number of parameters is predefined in the file. Note: Incorrect use of the dd command can cause data loss. Edit as Administrator: opens a file in a Gedit window running with administrator (root) privileges. The same can also be added to the value of the variable named 'GRUBCMDLINELINUXDEFAULT' and either would work. Look for the line containing 'GRUBCMDLINELINUX' and edit it as follows. Note: Have good backups before updating the BIOS.Įven though you have a lot of memory, a swap partition or /swapfile is still recommended. Ipv6 can also be disabled by editing the grub configuration file. There is no output, and the values are reloaded without a reboot. Note: Confirm that I have the correct web page for your motherboard model #. Use the -p option to reload default values from the /etc/nf and /etc/sysctl.d/ files: sysctl -p. There's a newer BIOS available that might help solve your problem, version 1.30, dated, and can be downloaded here. Once changes are persisted, they can be reloaded at any time by running the following command in sysctl: sudo sysctl -p. Run one of the following commands to open the file with your preferred editor. Add the following lines to /etc/nf if you have 512MB RAM or more. Add the following lines to the bottom of the /etc/nf file: 10485760 10485760. on Linux sudo sysctl -p /etc/nf on FreeBSD sudo /etc/rc.d/sysctl reload You can also add the line manually to your /etc/nf file. You could also use gksudo gedit . First you need to make a backup copy of /etc/nf file using the following command.where could be vim or nano or any other editor command, and is the one you need to edit. Get at least one complete pass of all the 4/4 tests to confirm good memory. Changing system settings requires superuser permissions. Controls the System Request debugging functionality of the kernel kernel. Swappiness setting ignored in systcl.Go to and download/run their free memtest to test your memory. linux sysctl sudo vi /etc/nf Kernel sysctl configuration file for Red Hat Linux For binary values, 0 is disabled, 1 is enabled.See sysctl(8) and nf(5) for more details. I looked for answer in askubuntu and on other sites, but I have not found the answer. Why are my settings in /etc/nf are not loading after reboot? etc/sysctl.d/nf:vm.swappiness = 60Īfter reboot, swappiness is again set to zero: $ sudo cat /proc/sys/vm/swappiness I have tried changing the swappiness setting in /etc/nf and /etc/nf - both are ignored after reboot (Ubuntu 12.04): $ sudo gedit /etc/nf CTRL + f vm.swappiness If found, edit it to say vm.swappiness. Swappiness is set to 0 and I can't change it. sudo -H gedit /etc/nf edit this file Search for an existing vm.swappiness entry.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |